Model · Multi-Output
Optima 302 — 13,500 mAh multi-output mini UPS with QC 3.0
The Optima 302 is the capacity step inside the multi-output family: 13,500 mAh behind the family's multi-voltage port set, with a QC 3.0 output for fast-charging a phone or tablet from the same unit and 24W of maximum output power.
Specifications — Optima 302
| Model | Optima 302 |
|---|---|
| Family | Multi-output mini UPS |
| Output power (max.) | 24W |
| Fast charging | QC 3.0 output |
| Capacity | 13,500 mAh |
Where the 302 fits
Buyers land on the 302 when the router-plus-modem set is settled but runtime is the complaint — the 13,500 mAh pack is the largest in the standard multi-output line below the C1, and the QC 3.0 port doubles the unit as a fast charger between outages. Confirm the exact port set for an order in the inquiry, with the device labels listed.
Ordering notes — Optima 302
The 302 suits buyers standardising a fleet on the slimmer case: check the typical install's device list against the port labels on the unit, and if any install in the fleet needs a 9V rail, that install belongs on the 301. Mixed fleets are common and easy to quote when the device lists arrive with the inquiry.
Who the 302's capacity step serves
At 13,500 mAh the 302 holds roughly a third more energy than the family's 10,400 mAh class while staying in the slim multi-output format, and that step exists for a specific complaint: the installation is right, the ports are right, but the battery runs short before the outage ends. Buyers reaching this page usually already know their device set — a router, a modem, perhaps a small switch — and have measured, or been told, that the smaller units in the family run short. The 302 answers with capacity rather than with a bigger case or a different architecture.
The honest comparison inside the family is three-way. Against the 301, the 302 trades a little size for the capacity step and adds a QC 3.0 fast-charge output. Against the C1, it gives up the 16,000 and 20,000 mAh tiers for a slimmer unit. Fleets that standardise should make that call once, at fleet level: a single model across every site simplifies sparing and replacement, and mixed fleets are only worth their complexity when the runtime data from real sites says the sites genuinely differ.
Running a 302 fleet day to day
A backup unit earns its keep invisibly, so fleet practice matters more than first impressions. Sites should be commissioned with the device list recorded against the unit — which loads hang on it, at which voltages — because the first outage report is far easier to interpret against a written list than against memory. When a site reports a short runtime, the list separates the three usual causes: a load that grew (a hungrier router swapped in during a repair), a battery at end of life, or an outage that simply outlasted the design assumption.
Spares policy follows from the same list. A fleet running one model can hold a small pool of spare units and swap first, diagnose later — the removed unit is bench-checked while the spare carries the shelf. That swap-first discipline is the practical reason the family is built as capacity tiers of shared formats rather than as unrelated models: the 302's spares logic is the 301's and the C1's, and a buyer growing from one tier to another does not have to relearn it.
What to send for a 302 quotation
Three facts make a 302 inquiry answerable in one pass: the device list with each load's rated voltage and current, the runtime the site must survive, and the quantity band. The device list confirms the port assignment; the runtime target confirms that 13,500 mAh is the right tier rather than the C1's larger builds; the quantity band prices it. Inquiries that arrive as a bare model number and a quantity get a price but not a configuration check, and the configuration check is where wrong-tier orders are caught.
Related pages
Ask for a quotation
Tell us the model, the output voltages your equipment needs and the quantity band for your order. If you are matching a UPS to a router, camera or terminal, add the device's rated voltage and current.